首页|基于滑模同步控制的履带式作业机全向调平系统研究

基于滑模同步控制的履带式作业机全向调平系统研究

扫码查看
原文链接
  • 国家科技期刊平台
  • NETL
  • NSTL
  • 万方数据
针对现有丘陵山区履带式作业机底盘大坡地作业时易侧翻、安全性差的问题,基于"三层车架"式丘陵山区履带式作业机结构方案,设计了一种互联式全向液压调平系统,提出了基于扰动观测器的滑模同步控制方法,降低了单液压缸位置误差以及双液压缸同步误差.AMEsim-Simulink联合仿真结果表明:基于滑模同步位置控制的履带式作业机全向调平系统优于传统PID控制,全向调平中20°横向调平时间减小1.6 s,25°纵向调平时间减小1.8 s,上升时间平均缩短21.8％,调平时间平均缩短35.5％,同步位置控制误差保持在±6 × 10-4 m内.在此基础上,对3层车架式丘陵山区履带式作业机样机进行了实机测试,其中全向调平机身倾角平均误差为2.55％,液压缸平均同步误差为8.2％,测试结果验证了履带式作业机全向调平系统的可行性与优越性.
Omnidirectional Leveling System of Crawler Machine Based on Sliding Mode Synchronous Position Control
Aiming at the problems that the chassis of crawler machine in hilly and mountainous areas is easy to roll over and the safety is poor,based on the developed structure scheme of"three-layer frame"crawler machine in hilly and mountainous areas,an interconnected omnidirectional hydraulic leveling system was designed to realize the pair-to-pair interconnection of four hydraulic cylinders in the upper frame that was horizontally levelled.The two hydraulic cylinders in the lower frame were connected in pairwise to realize longitudinal leveling.This system can make the center point of the crawler machine unchanged in horizontal leveling and longitudinal leveling.On this basis,a synchronization control strategy was proposed,which was based on the sliding mode synchronization control method based on disturbance observer.This method reduced the position error of single hydraulic cylinder and synchronous error of double hydraulic cylinder,and improved the stability of the system.The mechanical model of the crawler machine and the hydraulic model of the interconnected omnidirectional hydraulic leveling system were built in AMEsim,and the controller model was built in Simulink.The co-simulation results showed that the omnidirectional leveling system based on sliding mode synchronous position control was superior to the traditional PID control.In omnidirectional leveling,the 20° transverse leveling time can be reduced by 1.6 s,the 25° longitudinal leveling time can be reduced by 1.8 s,the average rising time was shortened by 21.8％,the average adjustment time was shortened by 35.5％,and the synchronous position control error was kept within±6 x 10-4 m.On this basis,the real machine test of the solid prototype of the"three-layer frame"crawler in hilly and mountainous areas was carried out.The average error of the tilt angle of the omnidirectional levelling body was 2.55％,and the average error of the hydraulic cylinder synchronization was 8.2％.The test results verified the feasibility and superiority of the designed omnidirectional levelling system of the crawler.

hilly and mountainous areascrawler machineomnidirectional levelingdisturbance observersliding mode synchronous controlpositioning control

汪若尘、苏兆睿、丁仁凯、孙泽宇、蒋俞、郭中阳

展开 >

江苏大学汽车与交通工程学院,镇江 212013

江苏大学汽车工程研究院,镇江 212013

江苏大学农业工程学院,镇江 212013

江苏超力电器有限公司,镇江 212300

展开 >

丘陵山区 履带式作业机 全向调平 扰动观测器 滑模同步控制 位置控制

国家自然科学基金面上项目江苏省自然科学基金项目镇江市重点研发计划项目江苏大学农业装备学部项目镇江市科技计划项目

51975253BK20210765ZD2022002NZXB20210101CQ2022004

2024

10.6041/j.issn.1000-1298.2024.04.039

农业机械学报
中国农业机械学会 中国农业机械化科学研究院

农业机械学报

CSTPCD北大核心
影响因子：1.904
ISSN：1000-1298
年,卷(期)：2024.55(4)
  • 23